![[logo] US EPA](http://www.epa.gov/epafiles/images/logo_epaseal.gif){kind=logo}
OSR-10
Quickfinder
TECHNICAL PRODUCT BULLETIN #SW-59
USEPA, OIL PROGRAM CENTER
ORIGINAL LISTING DATE: JUNE 28, 2011
"OSR-10"
| I. NAME, BRAND, OR TRADEMARK |
| OSR-10 Type of Product: Surface Washing Agent |
| II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT |
| MAG7 Venture Group, LLC DBA MAG7 Technologies 1 Lepage Place, Suite 100 Syracuse, NY 13206 Phone: (855) 255-6247 Fax: (855) 255-6247 E-mail: greg.goodell@mag7venturegroup.com or trevor.quig@mag7venturegroup.com Web Site: www.mag7technologies.com/OSR10 (Mr. Greg Goodell or Mr. Trevor Quig) |
| III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS |
| MAG7 Venture Group, LLC DBA MAG7 Technologies 1 Lepage Place, Suite 100 Syracuse, NY 13206 Phone: (855) 255-6247 Fax: (855) 255-6247 E-mail: greg.goodell@mag7venturegroup.com or trevor.quig@mag7venturegroup.com Web Site: www.mag7technologies.com/OSR10 (Mr. Greg Goodell or Mr. Trevor Quig) |
| IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION |
| 1. Flammability: Non-flammable 2. Ventilation: Move subject to fresh air. If breathing is difficult, obtain medical help. 3. Skin and eye contact; protective clothing; treatment in case of contact: Wash affected skin area with water. Consult physician of irritation persists. Skin irritation will not occur with most users. Flush eyes with a large amount of water for at least 15 minutes. Consult physician if irritation persists. Wear safety glasses and neoprene or rubber gloves during application. 4.a. Maximum storage temperature: 120°F 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 40°F to 120°F 4.d. Temperatures of phase separations and chemical changes: NA. Phase separation will not occur within the storage range. Product should be stored out of direct sunlight unless it is in an Ultraviolet (UV) light resistant container. |
| V. SHELF LIFE |
| 2 years in a sealed (unopened) container (tote, drum, pail) as delivered. 1 year in an opened container). |
| VI. RECOMMENDED APPLICATION PROCEDURE | ||||||||
| 1. Application Method: Apply OSR-10 to oil or contaminant with sprayer, pressure washer, mop, sponge, or brush. Application times will depend on the level of contaminant with a minimum of 10 minutes recommended soak time. The required soak time to remove oil will vary with oil density and degree of weathering. OSR-10 separates the oil from the physical surface to allow the oil to be sprayed off with a water rinse. OSR-10 should be mixed into soil applications and agitated to increase the effectiveness and reduce the application time. 2. Concentration/Application Rate: Dilution ratios for most applications range from 2 to 1 (parts water to parts OSR-10) to 15 to 1 (parts water to parts OSR-10). Dilution ratios are dependent on the contamination level and application with heavier crude oil spills requiring a lower dilution ratio. Rinse with water after usage for residue free surface. Surface cleaning typically requires 5 to 1 or 10 to 1 dilution ratio. These dilution ratios will require 1 gallon of OSR-10 per 300 square feet of surface area. These dilution ratios can be used in many applications including shorelines, rocks, and beaches. 3. Conditions for Use: Salt or fresh water (temperature ranges from 35°F to 120°F). Oil or contaminant can be skimmed from the water or rinsed and captured into collection containers and disposed of per local, state, and federal regulations.
|
| VII.TOXICITY AND EFFECTIVENESS | |||||||||||||||||||
a. Toxicity:
NA |
| VIII. MICROBIOLOGICAL ANALYSIS |
| NA |
| IX. PHYSICAL PROPERTIES |
| 1. Flash Point: 143°F 2. Pour Point: 20°F 3. Viscosity: 37 SUS @60°F 4. Specific Gravity: 1.1672 @60°F 5. pH: 11.5 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: CONFIDENTIAL 9. Solubility: Complete in water |
| X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS | ||||||||||||||||||||||
|