Jump to main content.


Basic Information about Mercury (inorganic) in Drinking Water

Mercury (Inorganic) at a Glance

Maximum Contaminant Level (MCL) = 0.002 milligrams per Liter (mg/L) or 2 parts per billion (ppb)

Maximum Contaminant Level Goal (MCLG) = 0.002 mg/L or 2 ppb

Health Effects
Some people who drink water containing mercury well in excess of the MCL over many years could experience kidney damage.

Drinking Water Health Advisories provide more information on health effects

Chemical Abstract Service Registry Number
7439-97-6

Sources of Contamination
Erosion of natural deposits; discharge from refineries and factories; runoff from landfills; runoff from croplands

List of all Regulated Contaminants (PDF) (6 pp, 396K, About PDF)

EPA regulates mercury in drinking water to protect public health. Mercury may cause health problems if present in public or private water supplies in amounts greater than the drinking water standard set by EPA.

What is mercury?
Mercury is a liquid metal found in natural deposits such as ores containing other elements.

Uses for mercury.
Electrical products such as dry-cell batteries, fluorescent light bulbs, switches, and other control equipment account for 50 percent of mercury used.

If you are concerned about mercury in a private well, please visit:

What are mercury's health effects?
Some people who drink water containing mercury well in excess of the maximum contaminant level (MCL) for many years could experience kidney damage.

This health effects language is not intended to catalog all possible health effects for mercury. Rather, it is intended to inform consumers of some of the possible health effects associated with mercury in drinking water when the rule was finalized.

Top of page

What are EPA's drinking water regulations for mercury?
In 1974, Congress passed the Safe Drinking Water Act. This law requires EPA to determine the level of contaminants in drinking water at which no adverse health effects are likely to occur. These non-enforceable health goals, based solely on possible health risks and exposure over a lifetime with an adequate margin of safety, are called maximum contaminant level goals (MCLG). Contaminants are any physical, chemical, biological or radiological substances or matter in water.

The MCLG for mercury is 0.002 mg/L or 2 ppb. EPA has set this level of protection based on the best available science to prevent potential health problems. EPA has set an enforceable regulation for mercury, called a maximum contaminant level (MCL), at 0.002 mg/L or 2 ppb. MCLs are set as close to the health goals as possible, considering cost, benefits and the ability of public water systems to detect and remove contaminants using suitable treatment technologies. In this case, the MCL equals the MCLG, because analytical methods or treatment technology do not pose any limitation.

The Phase II Rule, the regulation for mercury, became effective in 1992. The Safe Drinking Water Act requires EPA to periodically review the national primary drinking water regulation for each contaminant and revise the regulation, if appropriate. EPA reviewed mercury as part of the Six Year Review and determined that the 0.002 mg/L or 2 ppb MCLG and 0.002 mg/L or 2 ppb MCL for mercury are still protective of human health.

States may set more stringent drinking water MCLGs and MCLs for mercury than EPA.

Top of page

How does mercury get into my drinking water?
The major sources of mercury in drinking water are erosion of natural deposits; discharge from refineries and factories; runoff from landfills; and runoff from croplands.

A federal law called the Emergency Planning and Community Right to Know Act (EPCRA) requires facilities in certain industries, which manufacture, process, or use significant amounts of toxic chemicals, to report annually on their releases of these chemicals. For more information on the uses and releases of chemicals in your state, contact the Community Right-to-Know Hotline: (800) 424-9346.

Top of page

How will I know if mercury is in my drinking water?
When routine monitoring indicates that mercury levels are above the MCL, your water supplier must take steps to reduce the amount of mercury so that it is below that level. Water suppliers must notify their customers as soon as practical, but no later than 30 days after the system learns of the violation. Additional actions, such as providing alternative drinking water supplies, may be required to prevent serious risks to public health.

If your water comes from a household well, check with your health department or local water systems that use ground water for information on contaminants of concern in your area.

Top of page

How will mercury be removed from my drinking water?
The following treatment method(s) have proven to be effective for removing mercury to below 0.002 mg/L or 2 ppb: coagulation/filtration, granular activated carbon, lime softening, and reverse osmosis.

Top of page

How do I learn more about my drinking water?
EPA strongly encourages people to learn more about their drinking water, and to support local efforts to protect the supply of safe drinking water and upgrade the community water system. Your water bill or telephone book's government listings are a good starting point for local information.

Contact your water utility. EPA requires all community water systems to prepare and deliver an annual consumer confidence report (CCR) (sometimes called a water quality report) for their customers by July 1 of each year. If your water provider is not a community water system, or if you have a private water supply, request a copy from a nearby community water system.

The CCR summarizes information regarding sources used (i.e., rivers, lakes, reservoirs, or aquifers), any detected contaminants, compliance and educational information.

Some water suppliers have posted their annual reports on EPA's Web site.

Other EPA Web sites

Top of page

Safewater Home | About Our Office | Publications | Questions and Answers | Links | Office of Water | En Español


Local Navigation


Jump to main content.