Jump to main content.


Basic Information about Dinoseb in Drinking Water

Dinoseb at a Glance

Maximum Contaminant Level (MCL) = 0.007 milligrams per Liter (mg/L) or 7 parts per billion
(ppb)

Maximum Contaminant Level Goal (MCLG) = 0.007 mg/L or 7 ppb

Health Effects
Some people who drink water containing dinoseb well in excess of the MCL over many years could experience reproductive difficulties.

Drinking Water Health Advisories provide more information on health effects

Chemical Abstract Service Registry Number
88-85-7

Sources of Contamination
Runoff from herbicide used on soybeans and vegetables

List of all Regulated Contaminants (PDF) (6 pp, 396K, About PDF)

EPA regulates dinoseb in drinking water to protect public health. Dinoseb may cause health problems if present in public or private water supplies in amounts greater than the drinking water standard set by EPA.

What is dinoseb?
Dinoseb is an organic solid -- yellowish crystals with a pungent odor.

Uses for dinoseb.
Its greatest use is as a contact herbicide for post-emergence weed control in cereals, undersown cereals, seedling lucerne and peas. Dinoseb is also used as a corn enhancer and an insecticide and miticide.

If you are concerned about dinoseb in a private well, please visit:

What are dinoseb's health effects?
Some people who drink water containing dinoseb well in excess of the maximum contaminant level (MCL) for many years could experience reproductive difficulties.

This health effects language is not intended to catalog all possible health effects for dinoseb. Rather, it is intended to inform consumers of some of the possible health effects associated with dinoseb in drinking water when the rule was finalized.

Top of page

What are EPA's drinking water regulations for dinoseb?
In 1974, Congress passed the Safe Drinking Water Act. This law requires EPA to determine the level of contaminants in drinking water at which no adverse health effects are likely to occur. These non-enforceable health goals, based solely on possible health risks and exposure over a lifetime with an adequate margin of safety, are called maximum contaminant level goals (MCLG). Contaminants are any physical, chemical, biological or radiological substances or matter in water.

The MCLG for dinoseb is 0.007 mg/L or 7 ppb. EPA has set this level of protection based on the best available science to prevent potential health problems. EPA has set an enforceable regulation for dinoseb, called a maximum contaminant level (MCL), at 0.007 mg/L or 7 ppb. MCLs are set as close to the health goals as possible, considering cost, benefits and the ability of public water systems to detect and remove contaminants using suitable treatment technologies. In this case, the MCL equals the MCLG, because analytical methods or treatment technology do not pose any limitation.

The Phase V Rule, the regulation for dinoseb, became effective in 1994. The Safe Drinking Water Act requires EPA to periodically review the national primary drinking water regulation for each contaminant and revise the regulation, if appropriate. EPA reviewed dinoseb as part of the Six Year Review and determined that the 0.007 mg/L or 7 ppb MCLG and 0.007 mg/L or 7 ppb MCL for dinoseb are still protective of human health.

States may set more stringent drinking water MCLGs and MCLs for dinoseb than EPA.

Top of page

How does dinoseb get into my drinking water?
The major source of dinoseb in drinking water is runoff from herbicide used on soybeans and vegetables.

A federal law called the Emergency Planning and Community Right to Know Act (EPCRA) requires facilities in certain industries, which manufacture, process, or use significant amounts of toxic chemicals, to report annually on their releases of these chemicals. For more information on the uses and releases of chemicals in your state, contact the Community Right-to-Know Hotline: (800) 424-9346.

Top of page

How will I know if dinoseb is in my drinking water?
When routine monitoring indicates that dinoseb levels are above the MCL, your water supplier must take steps to reduce the amount of dinoseb so that it is below that level. Water suppliers must notify their customers as soon as practical, but no later than 30 days after the system learns of the violation. Additional actions, such as providing alternative drinking water supplies, may be required to prevent serious risks to public health.

If your water comes from a household well, check with your health department or local water systems that use ground water for information on contaminants of concern in your area.

Top of page


How will dinoseb be removed from my drinking water?
The following treatment method(s) have proven to be effective for removing dinoseb to below 0.007 mg/L or 7 ppb: granular activated carbon.

Top of page

How do I learn more about my drinking water?
EPA strongly encourages people to learn more about their drinking water, and to support local efforts to protect the supply of safe drinking water and upgrade the community water system. Your water bill or telephone book's government listings are a good starting point for local information.

Contact your water utility. EPA requires all community water systems to prepare and deliver an annual consumer confidence report (CCR) (sometimes called a water quality report) for their customers by July 1 of each year. If your water provider is not a community water system, or if you have a private water supply, request a copy from a nearby community water system.

The CCR summarizes information regarding sources used (i.e., rivers, lakes, reservoirs, or aquifers), any detected contaminants, compliance and educational information.

Some water suppliers have posted their annual reports on EPA's Web site.

Other EPA Web sites

Top of page

Safewater Home | About Our Office | Publications | Questions and Answers | Links | Office of Water | En Español


Local Navigation


Jump to main content.