Basic Information about Styrene in Drinking Water
Styrene at a Glance
Maximum Contamiant Level (MCL) = 0.1 milligrams per Liter (mg/L) or 100 parts per billion (ppb)
Maximum Contaminant Level Goal (MCLG) = 0.1 mg/L or 100 ppb
Some people who drink water containing styrene in excess of the MCL over many years could have problems with their liver, kidney, or circulatory system problems.
Chemical Abstract Service Registry Number
Sources of Contamination
Discharge from rubber and plastic factories; leaching from landfills
EPA regulates styrene in drinking water to protect public health. Styrene may cause health problems if present in public or private water supplies in amounts greater than the drinking water standard set by EPA.
- What is styrene?
- Uses for styrene.
- What are styrene's health effects?
- What are EPA's drinking water regulations for styrene?
- How does styrene get into my drinking water?
- How will I know if styrene is in my drinking water?
- How will styrene be removed from my drinking water?
- How do I learn more about my drinking water?
If you are concerned about styrene in a private well, please visit:
What are styrene's health effects?
Some people who drink water containing styrene well in excess of the maximum contaminant level (MCL) for many years could have problems with their liver, kidney, or circulatory system problems.
This health effects language is not intended to catalog all possible health effects for styrene. Rather, it is intended to inform consumers of some of the possible health effects associated with styrene in drinking water when the rule was finalized.
What are EPA's drinking water regulations for styrene?
In 1974, Congress passed the Safe Drinking Water Act. This law requires EPA to determine the level of contaminants in drinking water at which no adverse health effects are likely to occur. These non-enforceable health goals, based solely on possible health risks and exposure over a lifetime with an adequate margin of safety, are called maximum contaminant level goals (MCLG). Contaminants are any physical, chemical, biological or radiological substances or matter in water.
The MCLG for styrene is 0.1 mg/L or 100 ppb. EPA has set this level of protection based on the best available science to prevent potential health problems. EPA has set an enforceable regulation for styrene, called a maximum contaminant level (MCL), at 0.1 mg/L or 100 ppb. MCLs are set as close to the health goals as possible, considering cost, benefits and the ability of public water systems to detect and remove contaminants using suitable treatment technologies. In this case, the MCL equals the MCLG, because analytical methods or treatment technology do not pose any limitation.
The Phase II Rule, the regulation for styrene, became effective in 1992. The Safe Drinking Water Act requires EPA to periodically review the national primary drinking water regulation for each contaminant and revise the regulation, if appropriate. EPA reviewed styrene as part of the Six Year Review and determined that the 0.1 mg/L or 100 ppb MCLG and 0.1 mg/L or 100 ppb MCL for styrene are still protective of human health.
States may set more stringent drinking water MCLGs and MCLs for styrene than EPA.
A federal law called the Emergency Planning and Community Right to Know Act (EPCRA) requires facilities in certain industries, which manufacture, process, or use significant amounts of toxic chemicals, to report annually on their releases of these chemicals. For more information on the uses and releases of chemicals in your state, contact the Community Right-to-Know Hotline: (800) 424-9346.
- EPA's Toxics Release Inventory (TRI) Web site provides information about the types and amounts of toxic chemicals that are released each year to the air, water, and land.
How will I know if styrene is in my drinking water?
When routine monitoring indicates that styrene levels are above the MCL, your water supplier must take steps to reduce the amount of styrene so that it is below that level. Water suppliers must notify their customers as soon as practical, but no later than 30 days after the system learns of the violation. Additional actions, such as providing alternative drinking water supplies, may be required to prevent serious risks to public health.
If your water comes from a household well, check with your health department or local water systems that use ground water for information on contaminants of concern in your area.
How will styrene be removed from my drinking water?
The following treatment method(s) have proven to be effective for removing styrene to below 0.1 mg/L or 100 ppb: granular activated carbon in combination with packed tower aeration.
How do I learn more about my drinking water?
EPA strongly encourages people to learn more about their drinking water, and to support local efforts to protect the supply of safe drinking water and upgrade the community water system. Your water bill or telephone book's government listings are a good starting point for local information.
Contact your water utility. EPA requires all community water systems to prepare and deliver an annual consumer confidence report (CCR) (sometimes called a water quality report) for their customers by July 1 of each year. If your water provider is not a community water system, or if you have a private water supply, request a copy from a nearby community water system.
Other EPA Web sites
- Find an answer or ask a question about drinking water contaminants on EPA's Question and Answer Web site or call EPA's Safe Drinking Water Hotline at (800) 426-4791
- EPA's Integrated Risk Information System
- EPA's Substance Registry System
- Technology Transfer Network Air Toxics web site, Styrene
Other Federal Departments and Agencies