Jump to main content.


EO ALL PURPOSE SOAP-LAVENDER

TECHNICAL PRODUCT BULLETIN #SW-50
USEPA, OIL PROGRAM CENTER
ORIGINAL LISTING DATE: NOVEMBER 17, 2010
“EO ALL PURPOSE SOAP-LAVENDER”


I. NAME, BRAND, OR TRADEMARK
EO ALL PURPOSE SOAP-LAVENDER
Type of Product: Surface Washing Agent

II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT
EO Products/Small World Trading Company
90 Windward Way
San Rafael, CA 94901
Phone: (415) 945-1900
Fax: (415) 945-7117
E-mail: patrick@eoproducts.com or michael@eoproducts.com
Web Site: http://www.eoproducts.com
(Mr. Patrick Butler or Mr. Michael Cronin)

III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS
UNFI East/Select Nutrition
P.O. Box 567
Keene, NH 03431
Phone: (603) 256-3000
(Ms. Missy Lamonreux)
Lotus Light
P.O. Box 1008
Scotts Valley, CA 95066
(Ms. Kate Lill)
UNFI West
1101 Sunset Boulevard
Rocklin, CA 95765
Phone: (916) 625-4100
(Ms. Kari Cluk)
Sales Outlet:
Whole Foods Austin
601 N Lamar Boulevard, Suite 200
Austin, TX 78703
Phone: (512) 476-1206
(Mr. Jeremiah McElwee)
Threshold
23 Janis Way
Scotts Valley, CA 95066
Phone: (800) 777-5677
(Ms. Linda Sims)
 

IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION
1. Flammability: Non-flammable (DOT: Non-hazardous)
2. Ventilation: Normal
3. Skin and eye contact; protective clothing; treatment in case of contact: Rinse thoroughly after use. Avoid eye contact. In case of such contact, immediately flush with large amounts of cool water for at least 15 minutes. Consult a physician if irritation develops. Protective gloves are recommended for extended or prolonged contact (e.g., immersing hands). Wear safety glasses if the method of use presents the likelihood of eye contact. Do not ingest. In case of ingestion, consult a physician.
4.a. Maximum storage temperature: 45°C
4.b. Minimum storage temperature: 4°C
4.c. Optimum storage temperature range: 22°C to 30°C
4.d. Temperatures of phase separations and chemical changes: Phase separation may occur at <15°C (but will restore to original condition at optimum temperature).

V. SHELF LIFE
Three (3) years (as delivered).

VI. RECOMMENDED APPLICATION PROCEDURE
1. Application Method: EO ALL PURPOSE SOAP may be applied by pouring, spraying (when diluted 1:4), dispensing equipment, or by scrubbing machines.
2. Concentration/Application Rate: Apply EO ALL PURPOSE SOAP full strength (undiluted) to surface area by pouring or with dispensing equipment concentrating on areas with heaviest contamination first. Apply diluted (1:4 dilution rate) EO ALL PURPOSE SOAP with sprayer. Agitate and scrub well. Rinse thoroughly. For heavily contaminated surfaces, EO ALL PURPOSE SOAP should always be used full strength (undiluted). For average to light contamination, EO ALL PURPOSE SOAP may be diluted from 2x-10x with water.
3. Conditions for Use: During cleaning, contain the oil soaked area and collect residue. For sand and vegetation cleaning, a berm may be constructed down slope that will collect the residue for disposal. All disposal of residue should be done according to federal, state, and local regulations. In general, the technique used for the collection of the oil/soap residue should be determined by the on-site contractor based on the environment of the area to be cleaned, and equipment and materials available for collection.

VII. TOXICITY AND EFFECTIVENESS
a. Toxicity:
Material Tested Species LC50 (ppm)
EO ALL PURPOSE SOAP Menidia beryllina
Mysidopsis bahia
21.33  96-hr
83.65  48-hr
 
No. 2 Fuel Oil Menidia beryllina
Mysidopsis bahia
8.95  96-hr
2.41  48-hr
 
EO ALL PURPOSE SOAP &
No. 2 Fuel Oil (1:10)
Menidia beryllina
Mysidopsis bahia
3.14  96-hr
2.37  48-hr
 
Reference Toxicant (SLS) Menidia beryllina
Mysidopsis bahia
12.04  96-hr
8.19  48-hr

b. Effectiveness:
NA


VIII. MICROBIOLOGICAL ANALYSIS
NA

IX. PHYSICAL PROPERTIES
1. Flash Point: >93°C
2. Pour Point: +24°F
3. Viscosity: 349.5 cst @ 40°C
4. Specific Gravity: 1.0208 @60°F
5. pH: 5.88
6. Surface Active Agents: PROPRIETARY
7. Solvents: PROPRIETARY
8. Additives: PROPRIETARY
9. Solubility: Miscible in oil, water, and solvents

X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS
Compound Concentration (ppm)
Arsenic <0.540
Cadmium <0.209
Chromium 0.202
Copper <0.205
Lead <0.494
Mercury <0.000388
Nickel 5.99
Zinc <0.204
Cyanide <1.15
Chlorinated Hydrocarbons <2.0



Local Navigation


Jump to main content.